Tire Pressure Sensor Relearn Procedures

Inflate all tires pressure to listed on tire placard
Turn the ignition switch to the ON position (engine off)
Press and release the MENU button on the EVIC until the message RETRAIN TIRE SENSOR-NO is displayed.
Press the STEP button to select YES.
Press the MENU button to start the relearn process. The EVIC will display the message, TRAIN LEFT FRONT TIRE.
Starting at LF tire, place relearn magnet over valve stem until horn sounds.
After horn sounds, proceed as in step 5 for the next 3 sensors in this order: RF RR LR SP (if equipped).
After the EVIC displays the message TRAINING COMPLETE, depress the STEP, C/T, RESET, or MENU buttons to exit the relearn procedure.

Ensure all tires are inflated to the pressure listed on the tire placard. Vehicle must be driven for at least 10 minutes while mainitnaing speed above 15 mph in order for system to learn new sensor IDs.

Inflate all tires to pressure listed on tire placard
Turn ignition to ON position (engine off)
Press and release the MENU button to start the relearn process the EVIC will display the message, TRAIN LEFT FRONT TIRE.
Press the STEP button to select YES.
Press the MENU button to start the relearn process, the EVIC will display the message TRAIN LEFT FRONT TIRE
Starting at LF tire, place relearn magnet over valve stem until horn sounds.
After horn sounds proceed as in step 5 for the next 3 sensors in this order RF RR LR SP (if equipped).
Once the EVIC displays the message TRAINING COMPELTE, depress the STEP, C/T, RESET, or MENU buttons to exit the relearn procedures

Relearn can be completed using a properly formatted scan tool and relearn magnet. *Relearn magnet not required for Prowler

With Standard Ignition.

Inflate all tires to pressure listed on tire placard
Turn ignition to OFF position and press and release brake pedal.
Cycle ignition from OFF to RUN position 3 times, ending in RUN position.
Press and release brake pedal.
Turn ignition to OFF position.
Cycle ignition from OFF to RUN position 3 times, ending in RUN position.
Horn will sound once and TPMS telltale will blink once train mode is initated. If equipped with message center, it will display TRAIN LF TIRE Place antennae of learn tool on sidewall of LF tire 180 degrees from valve stem to activate sensor. Horn will sound once sensor has been regonized, Repeat step for RF RR and LR tires.
After training LR tire the message center will display TRAINING MODE COMPLETE. If the vehicle is not equipped with the message center display, successful completion can be verified by turning the ignition to the OFF position and not hearing the horn sound. If the horn sounds, the training procedure must be repeated.

With Push-button Start:

With vehicle off, press and release the brake pedal.
Using the push button, press and hold the button until the vehicle is in accessory mode: WARNING: DO NOT PUSH AND RELEASE TOO QUICKLY...PUSH---WAIT FOR SOUND—RELEASE
Power off by pushing the button 1 time.
Repeat 3 times ending in ON position.
Press and release brake pedal.
Using the push button, press and hold the button until the vehicle is in accessory mode.
Power off by pushing the button 1 time.
Repeat 3 times ending in ON posiiton.
Horn will sound once and TPMS telltale will blink once train mode is initated. If equipped with message center it will display TRAIN LF TIRE.
Starting at LF tire, decrease air pressure until horn chirps. Repeat procedure for remaining tires in the following order: RF RR and LR. If equipped with bended sensors, Place antennae of learn tool on sidewall of LF tire 180 degree turn from valve stem to activate sensor. Horn will sound once sensor has been recongized. Repeat step for RF RR and LR tires.
After successfully programming the LR tire, the message center should display "TRAINING COMPLETE."
Inflate all tires to pressure listed on tire placard.

Inflate all tires to pressure listed on tire placard
Turn ignition to OFF position.
Cycle ignition from OFF to RUN position 3 times, ending in RUN position.
Press and release brake pedal.
Turn ignition to OFF position.
Cycle ignition from OFF to RUN position 3 times ending in RUN position.
Horn will sound once and TPMS telltale will blink once train mode is initated, if equippped with message center it will display TRAIN LF TIRE. Place relearn magnet on LF sensor when horn sounds.
Proceed as in step 6 for the next 3 sensors in the following order RF RR and LR.
After training LR the horn will sound and message center will display TIRE TRAINING MODE COMPLETE if equipped.

For Models Without Message Center

Inflate all tires to pressure listed on tire placard
Press and hold odomoter reset button until TIRE PRESSURE SET is displayed.
Hold button for 3 more seconds
TPMS telltale will then begin to blink to signal completion of reset process.

For models with message center:

Press and hold SETUP button until RESET FOR SYSTEM CHECK is displayed.
Press and hold RESET button until HOLD RESET TO RELEARN is displayed.
Press and hold RESET button for 3 seconds.
TPMS telltale and HOLD RESET TO RELEARN message will blink 3 times to signal completion of reset process.

Inflate all tires to pressure listed on tire placard
Turn ignition to ON position.
If not equipped with RESET BUTTON:
- Press the Trip/Odometer button until TIRE RESET or CHECK TIME and RESET appear.
- Press and hold button for 3 seconds until TPMS telltale blinks 3 times and turns off.
If equipped with RESET button:
- Press and hold TIRE RESET BUTTON (on instrument panel, behind left side of steering wheel for 3 seconds.TPMS telltale should blink 3 times and turn off.

Inflate all tires to pressure listed on tire placard
Turn ignition to OFF position and press and release brake pedal.
Cycle ignition from OFF to RUN position 3 times, ending in RUN position.
Press and release brake pedal.
Turn ignition to OFF position.
Cycle ignition from OFF to RUN position 3 times, ending in RUN position.
Horn will sound once and TPMS telltale will blink once train mode is initated. If equipped with message center, it will display TRAIN LF TIRE Place antennae of learn tool on sidewall of LF tire 180 degrees from valve stem to activate sensor. Horn will sound once sensor has been regonized. Repeat step for RF RR and LR tires.
After training LR tire the message center will display TRAINING MODE COMPLETE. If the vehicle is not equipped with the message center display, successful completion can be verfied by turning ignition to the OFF position and not having the horn sound, if the horn sounds the training procedure must be repeated.

Place the ignition in the off position and keep the key in the ignition. Cycle the ignition to the on position (engine off).
Turn the hazard flashers on and then off three times. This must be accomplished within 10 seconds.
The horn will chirp and “TRAIN LEFT FRONT TIRE” will appear on the message center along with the MIL.
Starting at LF tire decrease air pressure until horn chirps. Repeat procedure for reamining tires in the following order RF RR and LR.
After successfully programming the LR tire the message center should display "TRAINING COMPLETE" and the MIL will no longer be illuminated.
Inflate all tires to pressure listed on the placard.

Keyless Entry Transmitter or Driver Information Center (DIC) Learn Enable Method

Ensure that no other learn procedure is being performed simultaneously within the same area. Stray signals from other TPM equipped vehicles may be unintentionally learned. If any random horn chirps are heard from the vehicle while performing learn procedure a stray sensor has been learned and the procedure will need to be cancelled and repeated. If the sensor activation does not cause the horn to chirp, it may be necesary to rotate the wheel about a half of a turn.
Turn ignition on and begin TPM learn mode by using one of the following procedures: On vehicles equipped with keyless entry, simultaneously press the keyless entry transmitters lock and unlock buttons until a double horn chirp sounds. The left front turn signal will also be illuminated. On vehicles not equipped with keyless entry, press and release driver information center DIC INFO button until the TIRE LEARN message appears on DIC display. Press and hold SET/RESET button until a double horn chirp sounds. The left front turn signal will also be illuminated. On vehicles without DIC buttons press and hold the trip odometer resett button until the relearn tire message is displayed.
Starting with left front tire, learn the sensor using the increase/decrease method.
Increase or decrease tire pressure for 8-10 seconds then wait for a horn chirp. The horn chirp may occur before or up to 30 seconds after the 8-10 second pressure increase/decrease time period has been reached. Once the horn chirp has sounded, the sensor information is learned and the turn signal in the next location to be learned wil illuminate
After the horn chirp has sounded and the right front turn signal is illuminated, repeat step 4 for the remailing 3 sensors in the following order: right front, right rear, and left rear.

Inflate all tires to pressure indicated on tire placard.
Turn ignition to ON position (engine off)
Press the RESET button found on passenger side instrument panel fuse box.
The TPMS telltale will blink 3 times and turn off.

Inflate all tires to pressure indicated on tire placard.
Turn ignition to ON position (engine off)
Press vehicle information button until TIRE INFLATION MONITOR SYSTEM PRESS SWITCH TO RESET is displayed
To reset low tire pressure condition, hold down the DOWN/LEFT arrow button until TIRE Inflation MONITOR SYSETM HAS BEEN RESET is displayed. Release DOWN/LEFT arrow button and TIRE PRESSURE NORMAL is displayed.
To reset system after tire rotation/replacement, hold down the DOWN LEFT arrow button for 5 seconds, Release DOWN/LEFT arrow button and TIRE PRESSURE NORMAL is displayed.

Inflate all tires to pressure indicated on tire placard.
Turn ignition to ON position (engine off)
Press GAUGE INFO button until TIRE PRESSURE is displayed
Hold down RESET BUTTON until TIRE PRESSURE RESET is displayed.
Release RESET button, TIRE PRESSURE NORMAL is displayed.

Inflate all tires to pressure indicated on tire placard.
Turn ignition to ON position (engine off)
Press GAUGE INFO button until TIRE PRESSURE is displayed
Hold down RESET BUTTON until TIRE PRESSURE NORMAL is displayed.

Turn ignition to ON position (engine off).
Press vehicle information button on the DIC until the message LEARN TIRE POSITIONS is displayed.
Press the SET/RESET button to enable vehicle learn mode. The horn will sound twice to indicate vehicle has entered learn mode and the DIC will display the message TIRE LEARNING ACTIVE.
Starting at LF tire, increase/decrease pressure until horn sounds.
After horn sounds proceed as in step 4 for the next 3 sensors in the following order: RF, RR, LR
After LR sensor has been learned the horn will sound twice, turn ignition to OFF position.
Adjust all tires to pressure listed on tire placard.

Apply parking brake. Turn ignition to ON position (engine off)
Turn headlight switch from OFF to parking lamps 4 times within 4 seconds. A double horn chirp will sound and the TPMS telltale will begin blinking to indicate the learn mode is enabled.
Starting at the LF tire increase/decrease pressure until horn sounds.
After horn sounds, proceed as in step 3 for the next 3 sensors in the following order : RF, RR LR.
After LR sensor has been learned, turn ignition to OFF position. Adjust all tires to pressure listed on tire placard.

*If headlight switch does not enable TPMS Learn Mode, use TPMS Learn button on dash.

Inflate all tires to pressure indicated on tire placard.
Turn ignition to ON position (engine off)
Hold down MODE button until DIC display reads LOW TIRE PRESSURE HOLD SET TO RESET.
Hold down SET Button until a chime sounds and TIRE PRESSURE RESET is displayed.
System will now sound a chime 3 times, and DIC will display TIRE PRESSURE NORMAL.

Turn the ignition to the ON position (engine off)
Using keyless entry system: press and hold lock and unlock button simultaneously until horn sound and release INFO button until TIRE LEARN message is indicated on display. Hold down SET/RESET button until horn sounds. LF turn signal is illuminated to indicate learn mode enabled.
Starting with LF tire, increase/decrease the pressure until horn sounds.
After horn sounds, proceed as in step 3 for the next 3 sensors in the following order, RF RR LR.
After LR sensor has been learned, turn ignition to OFF position. Adjust all tires to pressure listed on tire placard.

Turn ignition to ACC position.
Press and hold unlock and lock buttons on the keyless entry transmitter until horn sounds.
Starting with LF tire increase/decrease, tire pressure until horn sounds.
After horn sounds proceed as in step 3 for the next 3 sensors in the following order; RF, RR, LR. After completing LR tire horn will sound twice.
Turn ignition to OFF position to exit vehicle learn mode. Adjust all tires to pressure listed on tire placard.

Turn ignition switch to ON position (engine off)
Press and hold unlock and lock buttons on the keyless entry transmitter; until horn sounds and then LF turn signal will become illuminated.
Starting with LF tire increase/decrease, tire pressure until horn sounds.
After horn sounds proceed as in step 5 for the next 3 sensors in the following order RF RR LR After completing LR tire horn will sound twice.
Turn ignition to OFF position to exit vehicle learn mode. Adjust all tires to pressure listed on the placard.

Apply parking brake. Turn ignition to ON position (engine off)
Press and hold unlock and lock buttons on the keyless entry transmitter until horn sounds, and then LF turn signal will become illuminated.
Starting with LF tire, increase/decrease tire pressure until horn sounds.
After horn sounds proceed as in step 5 for the next 3 sensors in the following order: RF RR LR After completing LR tire horn will sound twice.
Turn ignition to OFF position to exit vehicle learn mode. Adjust all tires to pressure listed on the placard.

Ensure all tires are inflated to the pressure listed on tire placard, When ignition is turned of, the system will be cleared and the TPMS telltale will turn off. The system will recalibrate when vehicle is operated at a speed of 30 mph for a minimum of 30 seconds.

Inflate all tires pressure listed on tire placard
Make sure the vehicle has been parked for at least 2 minutes before proceeding.
Turn the ignition switch to the ON position (engine off).
Press the reset button on the Driver Information Center (DIC) to clear any warning messages displayed on the Instrument Panel Cluster (IPC).
Press and release the OPTIONS button on the DIC until the IPC display is blank.
Press and hold the RESET button on the DIC for three seconds.
Press and release the OPTIONS button again until the message TIRE TRAINING appears on the IPC.
Press and release the RESET button until the message LEARN L FRONT TIRE is displayed.
Starting at left front tire, place relearn magnet over valve stem until horn sounds.

Inflate all tires pressure listed on tire placard
Turn the ignition switch to the ON position (engine off)
Press the RESET Button on the DIC to clear any warning messages.
Press and release the OPTIONS button on the DIC until the display is blank.
Press and hold the RESET button on the DIC for three seconds.
Press and release the OPTIONS button again until the message TIRE TRAINING is displayed.
Starting at LF tire, place relearn magnet over valve stem until horn sounds.
After horn chirp, has sounded, proceed as in step 6 for the next three sensors in the following order RF, RR, LR..
Turn the ignition switch to the OFF position to exit the relearn mode.

Connect compatible scan tool to Data Link Connector (DLC) and follow directions on display.

*Using Light Switch

Inflate all tires to pressure listed on tire placard
Turn ignition to ON position (engine off)
Turn the light swtich from OFF to Parking Lamps 3 times within 5 seconds.

*Using Radio

Inflate all tires to pressure listed on tire placard
Turn ignition to ON position (engine off)
Turn radio off
Hold DISP button until SETTINGS is displayed.
Use SEEK buttons to scroll down until TIRE MON is displayed.
Press the PREV or NEXT buttons until RESET is displayed.
Press the DIS button, a chime will sound and DONE is displayed.
Scroll until EXIT is displayed press DISP, chime sounds to signal exit from learn mode.

Turn ignition to the ACC position.
Press and hold unlock and lock buttons on the keyless entry transmitter until horn sounds and LF tire signal is illuminated. Or using the DIC, press and release IINFO button until TIRE LEARN message is indicated on display hold down SET/RESET button until horn sounds and LF tire signal is illuminated
Starting with LF tire, increase/decrease the pressure until horn sounds
After horn sounds proceed as in step 4 for the next 3 ensors in the following order: RF RR LR. After completing LR tire horn will sound twice.
Turn ignition to OFF position to exit vehicle learn mode Adjust all tires to pressure listed on tire placard.

Inflate all tires to pressure listed on tire placard
Turn ignition to ON position (engine off)
Press the RESET button on the driver's side of instrument fuse panel box.
The OIL CHANGE indicator will blink.
Press RESET button, CHANGE OIL indicator will turn off and TPMS telltale will blink.
Hold down RESET button until a chime is heard TPMS telltale is no longer displayed.

Inflate all tires to pressure listed on tire placard
Turn ignition to ON position (engine off)
Press and SELECT right arrow button located on the DIC until GAUGE is displayed.
Press SELECT down arrow button to display TIRE PRESSURE.
Hold down RESET button until TIRE PRESSURE RESET is displayed.
Release RESET button and the message TIRE PRESSURE NORMAL will be displayed.

Inflate all tires to pressure listed on tire placard
Turn ignition to RUN position.
Press vehicle information button until PRESS TO RESET TIRE PRESSURE is displayed.
Hold down SET/RESET button until TIRE PRESSURE RESET is displayed, then release button.

Turn ignition to RUN position
Press and hold unlock and lock buttons on the keyless entry transmitter until horn sounds.
Starting with LF tire increase/decrease the pressure until horn sounds.
After horn sounds proceed as in step 3 for the next 3 sensors in the following order: RF, RR, LR, After compelting LR tire horn will sound twice.
Turn igniton to OFF position to exit vehicle learn mode. Adjust all tires to pressure listed on tire placard.

Inflate all tires to pressure indicated on tire placard.
Start the engine.
Press and release the SELECT button on the DIC until GAUGE PAGE appears on the DIC display.
Press and release the SELECT button again until the message TIRE PRESSURE LOW is displayed.
Press and hold the RESET button on the DIC until the message changes to TIRE PRESSURE NORMAL.
Release the RESET button.

Apply parking brake.
Turn ignition to ON position (engine off)
Press the MENU button on the DIC (located on turn signal lever on Camaro and on instruemnt cluster for all others) until the vehicle's tire pressures are displayed.
Press Set/Cir (this button is located at the end of the turn signal lever on Camaro). Vehicle asks “Are you sure that you want to relearn?” Select Yes.
Starting at LF tire, decrease air pressure until horn chirps. Repeat procedure for remaining tires in the following order: RF, RR, and LR. After completing LR tire, horn will sound twice.
Turn ignition to OFF position to exit vehicle learn mode. Adjust all tires to pressure listed on tire placard.

Drive vehicle abover 19mph for a minimum of 30 seconds.

Inflate all tires to pressure indicated on tire placard.
Turn ignition to ON position (engine off).
Press the SELECT right arrow button located on the DIC until GAUGE is displayed.
Press SELECT down arrow button to display TIRE PRESSURE.
Hold down RESET button until TIRE PRESSURE RESET is displayed.
Release RESET button and the message TIRE PRESSURE NORMAL will be displayed.

Set parking brake
Turn ignition ot ON/RUN (engine off)
Use the MENU button to select the Vehicle Information menu in the Driver Information Center (DIC).
Use thumbwheel to scroll to the Tire Pressure menu item screen.
Press the SET/CLR button to begin sensor matching process. A message requesting acceptance of the process should display.
Press the SET/CLR button again to confirm selection.
Starting with LF tire, increase/decrease tire pressure until horn sounds, or use TPMS relearn tool to activate each sensor.
After horn sounds proceed as in step 5 for the next 3 sensors in the following order: RF, RR, LR. After completing LR tire, horn will sound twice.
Turn ignition to OFF position to exit vehicle learn mode. Adjust all tires to pressure listed on tire placard.

Ensure all tires are inflated to the pressures listed on the tire placard.
Put ignition to ON/RUN position (engine running).
Using the steering wheel’s right-side keypad, select “Settings,” “Display Options,” then “Tire Pressure” to turn on the Tire pressure readout display.
Exit the “Settings” menu and scroll to the Tire Pressure screen.
Hold down button SEL until the horn sounds twice.
Starting with the Left Front tire, use the scan tool to scan each sensor in the following order: LF, RF, RR, and LR. The horn will sound after each activation.
After completing LR tire, the horn will sound twice to complete relearn.

Sensor Relearn Procedure

Ensure all tires are inflated to the pressures listed on the tire placard.
Turn the ignition switch to the ON position (engine off) and lower the driver side window.
Scroll to the Tire Pressure screen using the steering wheel buttons then hold down the checkmark button until the horn sounds.
Starting with the Left Front tire, use the scan tool to scan each sensor in the following order: LF, RF, RR, and LR. The horn will sound after each activation. After completing LR tire, the horn will sound twice to complete relearn.
Turn ignition to the OFF position.

Sensor Relearn Procedure (select models)

Ensure all tires are inflated to the pressures listed on the tire placard.
Turn the ignition switch to the ON position (engine off) and lower the driver side window.
Press and release the trip odometer button to scroll to the Tire Pressure display.
Hold down the trip odometer button for five seconds then press the button again to confirm.
Starting with the Left Front tire, use the scan tool to scan each sensor in the following order:
LF, RF, RR, and LR. The horn will sound after each activation. After completing LR tire, the
horn will sound twice to complete relearn.

Sensor Relearn Procedure if equipped with Keyless entry (select models):

Ensure all tires are inflated to the pressures listed on the tire placard.
Place the ignition into the ON position (engine OFF) and lower the driver side window.
Using the keyless entry remote (key fob), press and hold the lock and unlock buttons simultaneously until the horn sounds.
Starting with the Left Front tire, use the scan tool to scan each sensor in the following order: LF, RF, RR, and LR. The horn will sound after each activation.
After completing LR tire, the horn will sound twice to complete relearn.
Turn ignition to the OFF position.

Sensor Relearn Procedure if equipped with Driver Info Center (select models):

Ensure all tires are inflated to the pressures listed on the tire placard.
Place the ignition into the ON position (engine OFF) and lower the driver side window.
Press the Vehicle Information button, located to the left or right of the instrument cluster, until “LEARN TIRE PRESSURES” is displayed. Then press the checkmark button.
Starting with the Left Front tire, use the scan tool to scan each sensor in the following order: LF, RF, RR, and LR. The horn will sound after each activation. After completing LR tire, the horn will sound twice to complete relearn.
Turn ignition to the OFF position.

Sensor Relearn Procedure if not equipped with Keyless Entry or DIC:

Ensure all tires are inflated to the pressures listed on the tire placard.
Place the ignition into the ON position (engine OFF) and lower the driver side window.
Press the trip odometer button until “LEARN TIRE PRESSURES” is displayed. Then hold down the trip odometer button.
Starting with the Left Front tire, use the scan tool to scan each sensor in the following order: LF, RF, RR, and LR. The horn will sound after each activation. After completing LR tire, the horn will sound twice to complete relearn.
Turn ignition to the OFF position.

Sensor Relearn Procedure

Ensure all tires are inflated to the pressures listed on the tire placard.
Turn the ignition switch to the ON position (engine off) and lower the driver side window.
Go into the Vehicle Info Menu using the MENU button located on the turn signal stalk.
Scroll to the Tire Pressure Menu using the rotator wheel, located to the left of the MENU button, press and hold the SET/CLR button (located at the end of the turn signal stalk) and then press it again.
Starting with the Left Front tire, use the scan tool to scan each sensor in the following order: LF, RF, RR, and LR. The horn will sound after each activation. After completing LR tire, the horn will sound twice to complete relearn.
Turn ignition to the OFF position.

Ensure all tires are inflated to the pressure listed on the tire placard. Drive vehicle at speeds above 15 mph for a minimum of 40 seconds. Sensor ID's will be learned automatically.

Inflate all tires to pressure listed on tire placard.
Hold down RESET button (on end of wiper lever) until DISPLAY TYPE is displayed.
Press button on end of wiper lever to select SET.
Press RESET button.
Press button on end of wiper lever to select TIRE PRESSURE.
Press RESET button.
Press button on end of wiper lever to select WHEEL CHANGE (select STORE PRESSURES if resetting air pressure).
Press RESET button. Relearn can take 20 minutes to complete.

Inflate all tires to pressure listed on tire placard.
Press CAR function button.
Select TIRE PRESSURE MONITORING.
Select WHEEL CHANGE (select STORE CURRENT TIRE PRESSURES if resetting tire pressures).
Relearn can take 20 minutes to complete.

Inflate all tires to pressure listed on tire placard.
Press CAR function button.
Select TIRE PRESSURE MONITORING.
Select INITIALIZE WHEELS (select STORE CURRENT TIRE PRESSURES if resetting tire pressures).
Relearn can take 20 minutes to complete.

Inflate all tires to pressure listed on tire placard.
Press MENU knob on center of console to access the start menu.
Rotate MENU knob to position arrow by SET.
Press MENU knob.
Move arrow to TIRE PRESSURE.
Press MENU knob.
Move arrow to STORE PRESSURES.
Press MENU knob, a check mark will appear to signal relearn completion.
Exit out of tire menu. Vehicle will need to be driven several minutes to complete relearn process.

Inflate all tires to pressure listed on tire placard.
Turn ignition to ON position (engine off).
Enter tire pressure mode.
Press media control, located on center console.
Let vehicle sit for 20 minutes.
After 20 minutes, vehicle must be driven above 25 mph for 10 minutes.

Equipped with iDrive:

Inflate all tires to pressure indicated on tire placard.
Turn ignition to ON position (engine off).
Press iDrive controller to use "i" menu.
Select SETTINGS, press iDrive controller.
Select CAR/TIRES, press iDrive controller.
You may need to switch to the top field, select TIRES:RDC, and press iDrive controller.
Start engine.
Select CONFIRM TIRE PRESSURE, press iDrive controller.
Vehicle must be driven to complete relearn.

Not equipped with iDrive:

Start engine.
Hold turn signal lever in the up or down position until TPMS telltale and RESET are displayed.
Press button at end of turn signal lever.
Press and hold button at end of turn signal lever until a check appears after RESET.
Vehicle must be driven to complete relearn.

Equipped with iDrive:

Inflate all tires to pressure indicated on tire placard.
Turn ignition to ON position (engine off)
Select SETTINGS from iDrive menu.
Select VEHICLE
Select TPM
Select RESET

Not equipped with iDrive:

Turn ignition to ON position (engine off)
Hold down TIRE PRESSURE WARNING or RDC button (located on insturment panel) until TPMS telltale is illuminated.
Vehicle must be driven to complete relearn.

A properly formatted scan tool (OBDII) is required to learn new sensor IDs when replacing sensors.

Ensure all tires are inflated to the pressure listed on the tire placard. Drive vehicle at speeds above 15 mph for a minimum of 40 seconds. Sensor ID's will be learned automatically.

A properly formatted scan tool (OBDII) is required to learn new sensor IDs when replacing sensors.

Ensure all tires are inflated to the pressure listed on the tire placard. Vehicle must be driven for at least 10 minutes while mainitnaing speed above 15 mph in order for system to learn new sensor IDs.

A properly formatted scan tool (OBDII) is required to learn new sensor IDs when replacing sensors.

Apply parking brake, Turn ignition to ON position (engine off)
Turn headlight switch from OFF to parking lamps 4 times within 4 seconds. A double horn chirp will sound and the TPMS telltale will begin blinking to indicate the learn mode is enabled).
Starting at the LF tire, increase/decrease pressure until horn sounds.
After horn sounds, proceed as in step 3 for the next 3 sensors in the following order: RF, RR, LR.
After LR sensor has been learned, turn ignition to OFF position. Adjust all tires to pressure listed on tire placard.

A properly formatted scan tool is required to learn new sensor IDs when replacing sensors.

Ensure all tires are inflated to the pressure listed on the tire placard, Vehicle must be driven for at least 10 minutes while maintaining speed above 15mph in order for system to learn new sensor IDs. If spare tire sensors ID is being programmed, a properly formatted scan tool is necessery.

Ensure all tires are inflated to the pressure listed on the tire placard, Drive vehicle above 15mph for a minimum of 20 minutes to complete relearn process, or use properly formatted scan tool.

Initializing the following rotation and tire replacement:

Inflate all tires to pressure indicated on tire placard.
Turn ignition to ON position (engine off).
Hold down tire pressure warning reset switch until TPMS telltale blinks 3 times.
It will take several minutes for the ECU to receive signals from the sensors and complete initialization.

Inflate all tires to pressure indicated on tire placard.
Turn ignition to ON position
Hold down tire pressure warning reset switch until Pressure Initial Indicator is displayed.
Vehicle will have to be driven at speeds above 19mph to complete initialization.

Properly formatted scan tool (OBDII) is required to learn new sensor IDs when replacing sensors.

Initializing the following rotation and tire replacement:

Inflate all tires to pressure indicated on tire placard.
Apply parking brake and turn ignition to ON position.
Hold down tire pressure warning reset switch until TPMS telltale blinks 3 times.
It will take several minutes for the ECU to receive signals from the sensors and complete initialization.

Initializing the following rotation and tire replacement:

Turn ignition to OFF position.
Inflate all tires to pressure listed on tire placard.
Start engine.
Hold down tire pressure warning reset switch until TPMS telltale blinks 3 times.
In several minutes, the multi-information display will display the air pressure in all 5 tires.
Turn engine off.

Ensure all tires are inflated to the pressure listed on the tire placard. Vehicle must be driven for at least 10 minutes while mainitnaing speed above 15 mph in order for system to learn new sensor IDs.

Ensure all tires are inflated to the pressure listed on the tire placard. Vehicle must be driven for at least 15 minutes while maintaining speeds above 12mph in order for system to learn new sensor IDs. If spare tire sensor ID is being programmed, a properly formatted scan tool is necessary or spare must be used on the vehicle and driven for a minimum of 16 minutes above 12 mph.

Inflate all tires to pressure indicated on tire placard.
Turn ignition to ON position (engine off).
Press arrow key (located on steering wheel) until tire air pressure is displayed on the combination instrument
Press the right reset button on the combination instrument.
Speedometer will display: MONITOR TIRE PRESSURE?: Select YES
Speedometer will display: TIRE PRESSRUE CONTROL ACTIVE!
The sensors will begin to monitor the pressure of all 4 tires. The message, TIRE PRESSURE CONTROL. PRESSURE DISPLAY AFTER SEVERAL MINUTES OF TRAVELING, will be displayed until pressure values can be stored.

Inflate all tires to pressure indicated on tire placard.
Turn ignition to ON then to OFF.
Wait 15 minutes.
Drive vehicle above 12 mph for several minutes.
Sensor IDs will then register.

Inflate all tires to pressure indicated on tire placard.
Turn ignition to OFF position and press and release the brake pedal.
Cycle ignition from OFF to RUN position 3 times, ending in RUN position.
Press and release brake pedal.
Turn ignition to OFF position
Cycle ignition from OFF to RUN position, 3 times ending in RUN position.
Horn will sound once and TPMS telltale will blink once train mode is initiated. If equipped with message center, it will display TRAIN LF TIRE. Place antennae of learn tool on side wall of LF tire 180 degrees from valve stem to activate sensor. Horn will sound once sensor has been recongized, Repeat step for RF, RR and LR tires.
After training LR tire, the message center will display TRAINING MODE COMPLETE. If the vehicle is not equipped with the message center display, successful completion can be verified by turning the ignition to the OFF position and not hearing the horn sound. If the horn sounds, the training procedure must be repeated.

Inflate all tires to pressure indicated on tire placard.
Turn ignition to ON position (engine off).
Press UP/DOWN button (on left side of steering wheel) until RUN FLAT INDICATOR ACTIVE, REACTIVATION POSS: + is displayed.
Press + button until TIRE PRES, NOW OK? NO YES is displayed
Press + button , RUN FLAT INDICATOR REACTIVATED.

Inflate all tires to pressure indicated on tire placard.
Turn ignition to ON position (engine off).
Press UP/DOWN button( on the left side of steering wheel) until TIRE PRESSURE MONITOR CONNECTED REACTIVATION USING + is displayed.
Press + button TIRE PRES. NOW OK? Is displayed.
Press button TIRE PRESSURE MONITOR REAVTIVATED is displayed.

RESET Air Pressure
1 Inflate all tires to pressure listed on tire placard.
Turn ignition to ON position (engine off).
Press forward/back button on steering wheel until trip and odometer are displayed.
Press UP/DOWN button until tire inflation pressure monitor is displayed
Hold down reset button (located on instrument cluster) until MONITOR CURRENT TIRE PRESSURE? Is displayed.
Press + button TIRE PRESS, MONITOR ACTIVATED-PRESS. DISPLAY AFTER DRIVING A FEW MINS. is displayed.
If REACTIVATE-TIRE PRESS. MONITOR! Appears, repeat relearn procedure.
If CHECK TIRES! appears, indicates tire pressure too low, adjust pressures accordingly
Relearn New Sensor Ids.
Ensure all tires are inflated to the pressure listed on the tire placard. Vehicle must be driven for at least 10 minutes, while maintaining speed above 15 mph in order for system to learn new sensor IDs. If spare tire sensor ID is being programmed, a properly formatted scan tool is necessary.

Inflate all tires to pressure indicated on tire placard.
Start engine
Hold reset button until TPMS telltale illuminates
Initialization will be completed once vehicle is driven.

Inflate all tires to pressure indicated on tire placard.
Turn ignition to ON position (engine off).
Hold reset button located on right side of steering wheel 4-6 seconds until TPMS telltale illuminates or set pressure is displayed on instrument panel.
Drive vehicle to complete initialization

A properly formatted scan tool (OBDII) is required to learn new sensor IDs when replacing sensors.

After a tire rotation or tire replacement, the system will relearn itself under normal driving conditions. A properly formatted scan tool (OBDII) is required to learn new sensor IDs when replacing sensors.

Inflate all tires to pressure indicated on tire placard.
Under MAIN MENU select TIRE PRESSURE, then SETTINGS.
Select tire type and size.
Wheel positions are learned during normal driving conditions.

Ensure all tires are inflated to the pressure listed on tire placard. System relearns during normal driving conditions.

Apply parking brake, Turn ignition to ON position (engine off)
Turn headlight switch from OFF to parking lamps 4 times within 4 seconds. A double horn chirp will sound and the TPMS telltale will begin blinking to indicate the learn mode is enabled.
Starting at the LF tire increase/decrease pressure until horn sounds.
After horn sounds proceed as in step 3 for the next 3 sensors in the following order: RF RR LR.
After LR sensor has been learned, turn ignition to OFF position. Adjust all tires to pressure listed on tire placard.

Inflate all tires to pressure indicated on tire placard.
Press the TPM (RDK) button on the cockpit switch panel.
The MIL will flash momentarily to indicate a manual relearn has been initiated.

A properly formatted scan tool (OBDII) is required to learn new sensor IDs when replacing sensors.

Inflate all tires to pressure indicated on tire placard.
Turn ignition to ON position (engine off)
Press and hold down drivers side door switch for 2 seconds, Release then press again for 2 seconds. Release, then press again for 5 seconds.
Place learn tool over LF tire and press activate/test button, then proceed to RF RR and LR. Sensors must be activated within 90 seconds.
When each sensor ID has been received by control module TPMS telltale will be displayed for 5 seconds.

If equipped with standard entry system, turn ignition to the ON position, then proceed to step 4.
If equipped with keyless entry system, turn ignition to the ACC position.
Using keyless entry system: hold lock and unlock buttons simultaneously until horn sounds, and then LF turn signal will become illuminated, proceed to step 5.
Using DIC; press and release INFO button until TIRE LEARN Message is indicated on display. Hold down SET/RESET until horn sounds and LF turn signal is illuminated.
Starting with LF tire, increase/ decrease tire pressure until horn sounds.
After horn sounds proceed as in step 5 for the next 3 sensors in the following order: RF, RR, LR. After completing LR tire horn will sound twice.
Turn ignition to OFF position to exit vehicle learn mode. Adjust all tires to pressure listed on tire placard.

Inflate all tires to pressure indicated on tire placard.
Turn ignition to ON position (engine off)
if TPMS telltale is flashing hold down tire pressure reset button (located on instrument panel, knee bolster or inside glove box) until telltale light goes off.
Once TPMS telltale is off, hold down tire pressure reset button until TPMS telltale flashes 3 times.
Drive vehicle at 19mph or more for over an hour to complete initailization.

Initialization following rotation and tire replacement.
Inflate all tires to pressure indicated on tire placard.
Turn ignition to ON position (engine off)
Hold down tire pressure reset button (located on instrument panel, knee bolster or inside gloveb ox) until TPMS telltale flashed 3 times.
Procedure is complete once all transmitter signals have been received by the ECU.

A properly formatted scan tool (OBDII) is required to learn new sensor IDs when replacing sensors.

Initialization following rotation and tire replacement.
Inflate all tires to pressure indicated on tire placard.
Turn ignition to ON position (engine off).
Hold down tire pressure warning reset switch until TPMS telltale blinks 3 times.
Initialization will be complete when ECU has received signals from all sensors. Process may take 2-3 minutes.
If initalization is not complete drive vehicle for approximately 20 minutes.

Inflate all tires to pressure indicated on tire placard.
Turn ignition to ON position (engine off)
Enter the information center setup menu and select TIRE PRESSURE.
Select STORE.
SYSTEM LEARNING will appear on the display and disappear after several minutes of driving.

Inflate all tires to pressure indicated on tire placard.
Press VEHICLE button to access tire pressure control menu.
Press the RDK key to enable tire pressure control.
If equipped with sensor in spare wheel, select SPARE WHEEL MONITORING.
Press NEW TARGET PRESSURES key. The current pressures can now be saved.

Inflate all tires to pressure indicated on tire placard.
Turn ignition to ON position (engine off).
Press the MENU button located on Instrument Cluster.
Use thumbnail knob to select TIRE PRESSURE
Press thumbnail knob to select
Use thumbnail knob to select STORE.
Press thumbnail knob to select.

Relearn Following Tire Rotation/Replacement
Inflate all tires to pressure indicated on tire placard.
Apply parking brake and turn ignition to the ON position (engine off)
Hold SET (or ESP) button (located next to gear shift until audio signal is heard. Audio signal confirms successful relearn.
Relearn Following Sensor Replacement
Inflate all tires to pressure indicated on tire placard.
Apply parking brake.
Vehicle needs to stand for 20 minutes in order for control module to enter learn mode.
Drive vehicle above 16 mph to register sensor IDs.

Inflate all tires to pressure indicated on tire placard.
Drive vehicle above 16 mph to register sensor IDs.

Ensure all tires are inflated to the pressure listed on tire placard. Vehicle must be driven above 25 mph for more than 10 minutes and then parked for more than 15 minutes for system to learn new sensor IDs or a properly formatted scan tool can be used to complete the relearn procedure.

A properly formatted scan tool (OBDII) is required to learn new sensor IDs when replacing sensors.

Unfortunately, we do not have relearn instructions available online for your vehicle.
Please contact us at 1-(888)-290-4588 so that we may assist you further.

Having Trouble? Please click here to take a look at our Troubleshooting Guide.